Featured project · Australia
22 kV containerised switchroom for an Australian client
eGearZone designed, simulated, manufactured, tested and exported a complete 22 kV switchroom in a shipping container for a client in Australia. The room arrived with the 22 kV switchgear, protection, metering and building services installed, wired and tested — ready to place and connect.
The design was modelled and simulated in ETAP before manufacture, and the switchroom was built and tested to the applicable Australian Standards.
Project at a glance
- Scope: design, ETAP simulation, manufacture, testing and export
- Voltage: 22 kV
- Enclosure: modified shipping container with personnel doors and HVAC
- Equipment: 22 kV circuit-breaker switchgear with protection relays, metering panel, LV services
- Destination: Australia
From design to dispatch
01
Design
Single-line diagram, layout and equipment specification to the client’s requirements.
02
ETAP simulation
The network was modelled and simulated in ETAP to verify ratings and protection before build.
03
Manufacture
Container fit-out, switchgear installation, cabling, earthing and building services.
04
Testing
Factory testing of the complete switchroom before dispatch.
05
Export
Packed, documented and shipped to Australia, ready to place and connect.
Australian Standards
Designed, manufactured and tested to the applicable Australian Standards, including:
- AS 2067:2016 — Substations and high voltage installations exceeding 1 kV a.c.
- AS 62271.200 — A.C. metal-enclosed switchgear and controlgear for rated voltages above 1 kV and up to and including 52 kV
- AS/NZS 3000:2018 — Electrical installations (the Wiring Rules)
- AS/NZS 61439 — Low-voltage switchgear and controlgear assemblies
- AS/NZS 3008.1.1 — Selection of cables for alternating voltages up to and including 0.6/1 kV
Exterior




Inside the switchroom






What we deliver
A containerised switchroom arrives as a finished room: switchgear installed, wired and tested inside a container that can be lifted, shipped and moved again when the project ends.
- Container structure and fit-out — doors, insulation, chequer-plate floor
- MV switchgear up to 22 kV, with protection relays
- Metering and LV distribution
- Lighting, small power and air conditioning
- Cable entries, earthing and lifting points
- ETAP studies, factory testing and export documentation
Why containerised
Relocatable
Move the switchroom to the next site instead of building a new one.
Fast to deploy
Arrives finished and tested — place it, connect it, commission it.
Built to standard
Designed and tested to the destination country’s standards — in this case, Australia.
Switchroom, switch room or E-house?
They are the same thing. A switchroom (or switch room) is a building that houses switchgear, protection and control equipment. When it is built in a factory and delivered as one transportable unit, it is often called an E-house, an electrical house or a prefabricated switchroom.
A containerised switchroom uses a modified shipping container as the building. It travels as standard freight, arrives fitted out and tested, and can be moved again if the site changes.
Questions
What is the difference between a switchroom and an E-house?
Nothing in practice. E-house is the common industry name for a factory-built, transportable switchroom. Our containerised switchrooms are E-houses built in a shipping-container shell. Read our guide: what is an E-house? Our switchrooms are also used in temporary power rental fleets.
Can you build a switchroom to Australian Standards?
Yes. Our 22 kV containerised switchroom for an Australian client was designed in ETAP and built and tested to the applicable Australian Standards before export. Tell us the standards in your specification and we will confirm compliance at quotation.
Can a containerised switchroom be relocated?
Yes. The container format is designed to be lifted and transported, so the switchroom can be moved to a new site and reconnected.
What studies come with the switchroom?
We model the design in ETAP. Load flow, short circuit, protection co-ordination and arc flash studies can be included; see our power system studies.
Need a containerised switchroom?
Send us your single-line diagram, voltage and site details — we will come back with a scope, programme and price.

